doc. no : qw0905-ldbk9033/tr3 rev. : a date : 18 - sep - 2007 surface mount tape and reel ligitek electronics co.,ltd. property of ligitek only ldbk9033/tr3 data sheet lead-free parts pb
note : the tolerances unless mentioned is 0.2mm,angle 0.5. unit=mm. note : 1.all dimension are in millimeter tolerance is 0.2mm unless otherwise noted. 2.specifications are subject to change without notice. 0.61typ 7.62max 0.31typ 1.07typ 1.4 2.5 12.0 0.3 9.3 polarity 2.0 carrier type dimensions part no. : ldbk9033/tr3 package dimensions 0.4 0.1 7.84 3.37 1.5 4.0 1.75 5.5 2.52 4.0 t 1.9 2.8 0.76max 0.13typ cathode 2.0 0.5 0.1 page1/7 ligitek electronics co.,ltd. property of ligitek only
16.0 1.0 178 2.0 ldbk9033/tr3 part no. 12.0mm tape,7"reel descriptionquantity/reel 1500 devices 14.2 1.0 74.0 1.5 reel dimensions part no. : ldbk9033/tr3 page 2/7 ligitek electronics co.,ltd. property of ligitek only
3/7 page unit ma ma mw a dbk ratings symbol 30 100 120 50 i f i fp pd ir part no. ldbk9033/tr3 parameter forward current peak forward current duty 1/10@10khz power dissipation reverse current @5v absolute maximum ratings at ta=25 ligitek electronics co.,ltd. property of ligitek only viewing angle 2 1/2 (deg) 30020 typ. -20 ~ +80 -30 ~ +100 t opr tstg operating temperature storage temperature typical electrical & optical characteristics (ta=25 ) spectral halfwidth nm forward voltage @20 ma(v) 4.0 303.5 typ. max. 470 lens dominant wave length dnm material blue ingan/gan emitted part no ldbk9033/tr3 note : 1.the forward voltage data did not including 0.1v testing tolerance. 2. the luminous intensity data did not including 15% testing tolerance. water clear color luminous intensity @20ma(mcd) 160 min. v 150 esd electrostatic discharge
fig.5 relative intensity vs. wavelength typical electro-optical characteristics curve ligitek electronics co.,ltd. property of ligitek only 1.03.04.0 0 1 1.0 r e l a t i v e i n t e n s i t y @ 2 0 m a wavelength (nm) 450 0.0 400500550 0.5 0.5 r e l a t i v e i n t e n s i t y @ 2 0 m a n o r m a l i z e @ 2 5 f o r w a r d v o l t a g e @ 2 0 m a n o r m a l i z e @ 2 5 20 ambient temperature( ) ambient temperature( ) 0 -20 -40 0.8 0 -40-20 100 80 60 40 20 0.0 60100 80 40 fig.4 relative intensity vs. temperature 2.5 1.0 0.9 1.1 1.5 1.0 2.0 fig.3 forward voltage vs. temperature 1.2 3.0 r e l a t i v e i n t e n s i t y n o r m a l i z e @ 2 0 m a f o r w a r d c u r r e n t ( m a ) forward current(ma) forward voltage(v) 2.05.0110 0.0 0.5 1.0 1.5 2.0 1001000 fig.2 relative intensity vs. forward current fig.1 forward current vs. forward voltage 2.5 3.0 1 10 100 1000 dbk chip part no. page4/7 ldbk9033/tr3 25% 75% -60 100%25% 50%0 -30 0 75% 50% 60 100% 30 fig.6 directive radiation
260 c max. 10sec.max note:1.wave solder and reflow soldering should not be made more than one time. 2.you can just only select one of the soldering conditions as above. 1~5 c/sec 120 sec.max. above 220 c 60 sec.max. preheat 180~200 c preheat 60 ~ 120 sec 120 3-2 pb-free reflow solder 240 150 temp. ( ) 3-1. lead reflow solder time 1~5 c/sec 5sec rising +5 /sec cooling -5 /sec 5/7 page 120 ~ 180 sec recommended soldering conditions 1. hand solder basic spec is Q 280 3 sec one time only. 120 ~ 150 2. wave solder preheat 245 5 within 5 sec soldering heat max. 260 ligitek electronics co.,ltd. property of ligitek only part no. ldbk9033/tr3
cleaning: use alcohol-based cleaning solvents such as isopropyl alcohol to clean the led. (a) recommended circuit. (b) the difference of brightness between led could be found due to the vf-if characteristics of led. esd(electrostatic discharge): static electricity or power surge will damage the led. use of a conductive wrist band or anti-electrosatic glove is recommended when handing these led. all devices, equipment and machinery must be properly grounded. led led circuit model a drive method: led is a current operated device, and therefore, requirer some kind of current limiting incorporated into the driver circuit. this current limiting typically takes the form of a current limiting resistor placed in series with the led. consider worst case voltage variations than could occur across the current limiting resistor. the forwrd current should not be allowed to change by more than 40% of its desired value. precautions for use: storage time: 1.the operation of temperatures and rh are : 5 ~35 ,rh<60%. 2.once the package is opened, the products should be used within a week. otherwise, they should be kept in a damp proof box with descanting agent. considering the tape life, we suggest our customers to use our products within a year(from production date). 3.if opened more than one week in an atmosphere 5 ~ 35 ,rh<60%, they should be treated at 60 5 fo r 15hrs. circuit model b ligitek electronics co.,ltd. property of ligitek only page 6/7 part no. ldbk9033/tr3
1.t.sol=235 5 2.immersion time 2 0.5sec 3.coverage R 95% of the dipped surface solderability test mil-std-202f: 208d mil-std-750d: 2026 mil-std-883d: 2003 iec 68 part 2-20 jis c 7021: a-2 mil-std-750d:2031.2 j-std-020 mil-std-202f: 107d mil-std-750d: 1051 mil-std-883d: 1010 jis c 7021: a-4 environmental test ir reflow temperature cycling 1.105 ~ 25 ~ - 55 ~ 25 30mins 5mins 30mins 5mins 2.10 cyeles 1.t=260 xc max. 10sec.max. 2. 6 min mil-std-202f: 107d mil-std-750d: 1051 mil-std-883d: 1011 jis c 7021: b-12 mil-std-202f:103b jis c 7021: b-11 mil-std-750d: 1026 mil-std-883d: 1005 jis c 7021: b-1 mil-std-883d:1008 jis c 7021: b-10 page ligitek electronics co.,ltd. property of ligitek only 1.ta=under room temperature as per data sheet maximum rating. 2.if=20ma 3.t=1000 hrs (-24hrs, +72hrs) thermal shock test high temperature high humidity storage test endurance test high temperature storage test low temperature storage test operating life test 1.ta=105 5 &-40 5 (10min) (10min) 2.total 10 cycles 1.ta=65 5 2.rh=90%~95% 3.t=1000hrs 2hrs 1.ta=-40 5 2.t=1000 hrs (-24hrs, +72hrs) 1.ta=105 5 2.t=1000 hrs (-24hrs, +72hrs) classification reliability test: test item test condition reference standard 7/7 part no. ldbk9033/tr3
|
